Four Garage Door Blog

Local Businesses Blog in Texas

What To Do If Your Garage Door Spring is broken

Garage Door Services TX

The garage Door Spring is broken

In the event that your garage door is unable to shut or open, it could be due to a damaged spring. If this is the case, you can repair a damaged spring simply by replacing the old one with a fresh spring.

Set the Door

When the spring is broken when the garage door is down position, you’ll need to raise it. It is possible to do this with the assistance of a companion since the door is heavy. The door should be lifted up and then set in the fully open position. This will help to ease the springs so that they don’t stretch and are in tension. To accomplish this, you’ll have to disconnect the bar that locks the chain from the mechanism.

Make the Door

After the door has been opened, Once the door is opened, attach a pair of vise grips to the side that has a broken spring. Make sure to do this underneath the final rolling wheel on the track. This will stop your door from going. Unplug the springs damaged and the garage door. Check that the pulleys are still in good working order. If the bearings or the pulleys are damaged, they must be replaced.

Get the latest Spring

Take note of the length of the spring that is broken with a tape measure. Also, you can determine the width of the spring that’s on your garage door. You can take these measurements to a retailer who has garage door parts that you can buy. Make sure you buy two springs that are the same in both length and diameter.

Install New Spring

Check the spring that isn’t broken at the door and observe where the cable is over the pulleys. Set the spring up over the door. Place the cable on the door and then tighten the cable to create tension. Be sure that the cable is not stretched by more than 1 inch.

Replace Unbroken Spring

Removing the springs from garage doors requires replacing both the damaged spring as well as the spring that is not broken. This is necessary since you must use springs with the same force. Remove your vise grips from the track, and then attach them to the opposite side. Unbroken spring removed, then place the new spring on top.

Test the Door

Connect the lock bar to the chain mechanism. The vise grips must be removed from the track, and proceed to lower the doors until it is on the level of the ground. In the event that your garage door can not touch the ground, you must restart the spring so that the door is lowered until it reaches the ground.

Tips

Lower and raise your garage doors to check your work. You’ll be able to discern if the springs are too loose or tight.

How You Can Fix Your Noisy Garage Door

Garage Door Repair Midlothian TX

Fix your noisy garage door

Staying at home should be a time of relaxation and enjoying time with the family. If you need a break from your hectic schedule, then just lounging around at home is a good option. However, all that peace and quiet could go down the drain if you got a garage door that’s making annoying noises whenever it’s opened or closed. It gets worse if your garage door is used quite often. 

Needless to say, it’s a situation that you want to get fixed as soon as possible. Allowing it to linger is not going to cause a lot of discomfort for you and your family. And that basically defeats the purpose of being at home and being able to enjoy your stay there with your loved ones. You won’t be able to savor the moments as much as you’d like.

So how can you fix your noisy garage door? Read on to find out what you can do about it:

Lubricate It

Several reasons could be behind why your garage door is being noisy. It could already be old and worn out or it could be because of a recent change of weather. Whatever the reason might be, the good news is that it’s relatively easy to fix. All you need to do is to add lubricant to all of the metal parts of your garage door. Make sure that you’re able to spray lubricant to the hinges, roller, and track. One thing that you need to realize is that this isn’t going to be over after just one session of lubrication. It’s an ongoing process and you need to repeat it after every six months.

Tighten the Door

A noisy garage door can also be caused at times by loose nuts and bolts. So you also need to check if that’s the case and do the appropriate steps to correct it. Tightening your door’s nuts and bolts is the first and easiest step to quieting down your garage door. You have to inspect your garage door for any loose components first. After that, tighten the nuts and screws using a socket or a wrench. However, you also need to be careful while you’re tightening as the nuts shouldn’t be too tight.

Hinges, Rollers, and Springs

Now if the two that were listed above weren’t the cause of the noise, then you might need to look at it even deeper. There might be a more serious problem behind your noisy garage door. For example, the hinges, rollers, or springs of your door might either need to be repaired or replaced. Just make sure that you call professionals to do it for you instead of trying to fix it yourself. 

The basic details above could at least give you an idea of how you can fix your noisy garage door. However, the bottom line is that you should never attempt to do it if it seems too serious as it can be dangerous and also could lead to more serious issues for your garage door. Garage Door Repair Midlothian TX will help you.

How to Get Rid of Garage Door Rust

Garage Door Repair Service Haslet TX

 Get rid of garage door rust

Metal garage doors are among the finest choices you have as far as garage doors go. Whether for homes or for commercial buildings, metal garage doors offer plenty of advantages that make them excellent choices and popular with both home and business owners.

In spite of all its benefits, there are some downsides to choosing a metal garage door. Perhaps one of the main ones is having to deal with rust. It might be convenient for you to simply ignore it at the start, but as it progresses and affects most of your door, you can’t help but do something about it.

The good news is that you can actually do it yourself. Yes, you can get clean off the rust on your own and without having to resort to getting help from professionals. There also shouldn’t be any rush in trying to replace your garage door. Read on if you’re interested in how to get rid of garage door rust by yourself.

Preparing Yourself to Get Rid of the Rust

One thing you need to be prepared for is the hard work. It’s not going to be that easy to rid your door of the rust, especially if it’s already accumulated to a point where it just doesn’t look bad but also impacts how your door operates.

You also can’t underestimate the amount of damage that rust can do to your door. It’s capable of eating through the metal that makes up the door and leaving it a mess with holes in it. As a result, significant amounts of dirt, as well as water from rain, can enter and cause even more problems.

Steps To Do It

The following are the actual steps that you need to follow to remove the rust and prevent the situation from getting even worse.

  1. The first step is to close your garage door. Start cleaning it by starting on the bottom panel with the use of warm water and dishwashing liquid. This mixture is effective in removing both dirt and oil from the door. Clean and then rinse the door carefully before allowing it to dry.
  1. The next step is to get a clean cloth and dip it in white vinegar as well as a steel wool pad. Use the cloth to wipe the rusty part of the door. To scrub the rust off, use the steel wool pad. Continue wiping and scrubbing until there’s no rust left.
  1. Use a palm sander to sand the areas that were affected by rust. By sanding the rusted areas, you’re actually going to aid the primer that you’ll apply later to stick to the door.
  1. Choose a zinc-chromate primer to apply to the metal. The primer will help keep rust from forming any further. Use a paintbrush to apply the primer to the parts of the door that you just finished sanding. 
  1. Apply rust-resistant paint to those areas of the garage door where you just applied the primer.

The above tips on how to get rid of garage door rust on your own should serve as your guide on doing it right. If you find it too much of a challenge, you could still choose to hire the services of a professional for help.

Visit your nearest Garage Door Repair Services in Haslet TX.

How to Clean Your Garage Door Properly

Garage Door Repair Service Wise County TX

Clean your garage door properly

So when was the last time that you cleaned your garage door? If you’re surprised at the question then you might want to check on your garage door ASAP. You’ll probably see that it’s already seriously dirty. Letting the elements – such as the wind or the rain – take care of it just won’t suffice anymore.

Now that you’ve finally noticed how dirty your garage door is, what can you do about it? The time has come to clean your garage door and you’ve got an opportunity to do it yourself. All you require now are some useful tips and a few tricks on how to do it the right way.

Here’s how to clean your garage door properly:

How to Clean a Steel Garage Door

The following are the steps that you need to follow if your garage door is made from pre-finished steel.

Step #1: Prepare one cup of mild detergent solution. The solution should contain less than 0.5 percent phosphate and five gallons of water. Use the solution to remove dirt and grime by wiping down the garage door. 

Step #2: For oil stains, use a solution of diluted bleach and water. Make sure that the garage door is completely rinsed so that the detergent and the bleach wouldn’t mix. When the stains are gone, you can rinse the door again.

Step #3: Don’t forget to include the top, sides, and behind the weather stripping of the garage door.

Step #4: If you find dirt that has caked on the door, you can easily remove it with just your hands or get any simple tool to help with the removal.

Step #5: Get a non-abrasive piece of sponge or cloth and use it to clean the garage door.

Step #6: Dry off the garage door using a dry piece of cloth after you’ve rinsed it.

How to Clean a Wooden Garage Door

The following are the steps that you need to follow to clean a wooden garage door properly.

Step #1: Use a solution that’s made up of mild detergent and water. Get a clean sponge and soak it into the solution before wiping away any dirt and debris on the door’s surface.

Step #2: Rinse the door thoroughly with the use of a light garden hose. Allow the garage door to dry completely.

Step #3: If you see that your garage door’s finish is already eroded or thinning, you can use the detergent solution to clean it before letting it dry. After it has dried, use an oil/alkyd primer for priming the affected areas. Follow it up either with complete priming or a coating of finish.

Step #4: Finish the cleaning procedure with a coat of finish, particularly if no eroded patches can be found on your wooden garage door.

Follow the steps above in order to clean your garage door properly. It really shouldn’t be a complicated process as long as you do it the right way and you use the right tools for the job. Or visit your nearest garage door repair services Wise County TX for any Services you might need.

Grayson Couty  Garage Door Opener Repair Tips

Garage Door Installation Grayson County TX

Garage Door Opener Repair Tips

Garage doors are an integral part of your house furnishing but unfortunately, most of the time they are left unattended whenever a repair of the household is undertaken. Hence many people are faced with problems the like as sticking or jammed doors, unwarranted opening of the doors, or the garage doors not staying open.

As far as sticking or jammed doors are concerned, it is usually because of deformed frames or channels through which the door slides and they can be easily repaired without much hassle. Usually, with a simple toolkit of a hammer, a wrench a few nuts and bolts, and a screwdriver, you can fix most of these problems by yourself. 

The erratic opening and closing of the door might be due to a depressed key in the opener control or there might be some problem with your garage door opener circuit that can easily be fixed. But the problem arises when some major part of your garage door develops a defect, for example, the gears of the door opener. In such cases, a more involved repair is required. Hopefully, the following steps would give you some useful insight about repairing and replacing the worn-out gears in your garage door opener.

You can understand if the gear has broken if your garage door even though the motor is working properly and the torsion springs are intact. These gears, usually made of plastic, are among the weaker parts of the opener and can be damaged due to several reasons like old age, prolonged usage without maintenance, imbalance in the garage door or may be due to a manufacturing defect.

But, with a few simple types of equipment and following the instructions properly, you can change these gears on your own.

First and foremost, you should disconnect the electric supply to the garage door to prevent any chance of electrocution and also so that no one operates the door while you are working on it. Next, you should close the door manually and remove it from the pulley to ensure that the door does not accidentally hurt you while you are servicing it. Now you are ready to set about repairing your garage door opener and replacing the gears.

If you are looking for professionals in Garage Door Repair in Grayson County TX. We are the ones.

Now you need to open the retainer cap of the belt pulley and remove the sprocket. Now you can remove the chain or belt from the sprocket after marking its position and tape it to prevent it from getting twisted up and messy. Then remove the end covers, the drive gear, the retaining clip, and the RPM sensor and also disconnect the motor. An assembly of nuts holds the motor to the shaft. You need to remove these nuts first. Once you have removed the motor from the driveshaft, you can remove the gear and replace it if necessary. Having replaced the gear, you need to start reassembling the entire system in the exact opposite manner. 

Take care to see to it that each part goes into the right place to avoid any further problems with your garage door. Thus, we see that changing the worn-out gears is a bit more involved. Hence, if you are not very confident about doing it yourself, you should call a professional garage door repair service to tend to the matter.

Garage Door Safety Tips You Should Follow

garage door repair corinth

Garage door safety tips

Garage doors provide additional security and protection to your home. They’re much more than just points of access to the space where you store your vehicle. A garage door also adds a layer of security that can give you some much-needed peace of mind.

In spite of what it brings to the table, garage doors also happen to pose some risks and dangers. Now that’s something that homeowners wouldn’t usually associate with garage doors, but it’s still true nevertheless. 

The dangers manifest themselves and become even worse when the garage door isn’t maintained properly. Still, it’s not too late to familiarize yourself with the potential dangers. It’s important so you can protect not just yourself but your entire family.

So what can you do about aloof those risks? Are there steps that you can take to keep yourself and your family safe while using your garage door on a daily basis? Below we take a look at some of the garage door safety tips you should follow.

Regular Inspections

One of the best and most important safety tips that you can follow is to make sure that your garage door is inspected and tested regularly. You can start by giving it a visual inspection as it will allow you to see if there are obvious signs of wear and tear.

You’ll need to carefully check the springs, cables, pulleys, and rollers of your garage door. But if you see that the springs or cables are damaged, make mo attempt to repair them yourself. It would be quite dangerous for you to attempt it and you need to contact professionals to do it for you instead.

Make Sure Kids Don’t Play With the Remote

Another safety tip that you need to follow is to make sure that kids don’t play with the remote control of your garage door. First of all, the remote control should simply be out of any child’s reach. With the garage door being one of the biggest and heaviest objects in your house, this needs to be a must. 

How do you make sure that it doesn’t happen? One way to do it is by placing the garage door opener control button about five feet above the floor. This will make it beyond the reach of little kids and you can easily view your garage door.

Don’t Leave the Garage Door Opener in the Car

You also shouldn’t leave the garage door opener in your car. It’s important because one of the most common ways for criminals to break into homes is by stealing the remote control of the garage door. 

In order to prevent this from happening, you only need to take your remote control with you any time you leave your car. It’s not hard anyway since it’s small and doesn’t weigh much. You can place it in your pocket, purse, or small bag.

Use Smart Garage Door Technology

Next in this list of garage door safety tips, you should follow is to make use of smart garage door technology. Invest in technologies that will allow you to monitor whether your garage door is being opened by someone who’s not supposed to. Those technologies can be used through your phone or another device that will help prevent any similar security problems from happening.

Visit your nearest Garage Door Repair in Corinth.

Your Guide to a Clean Garage

lantana garage door repair

Guide to a clean garage

Proper cleaning of your garage is one of those regular tasks that you need to do right. It also extends to your garage door. After all, your garage door is used even more often than the rest of the garage itself. So it only makes sense to make sure that it’s all cleaned properly and regularly.

Cleaning your garage is essential, even if only done from time to time. It’s part of ensuring that your garage and garage door are well maintained. So even though they are made well-made and durable, it could still add to their longevity. And for you, it would mean a more comfortable use of both your garage and garage door.

Look at the following and treat it as your guide to a clean garage. These are simple steps that you can follow to guarantee the cleanest version of your garage ever.

Step #1 to a clean garage door

– The very first step that you need to take is to wipe down all of the flat surfaces using a multipurpose spray. You need to do the same to the shelves in your garage. There might be an urge to start cleaning the floor first. But if you can resist that urge and do it later, then you’ve made the correct first step in ensuring a clean garage and garage door.

Step #2 to a clean garage door

– The next step is to clean the Slatwall panels of your garage. To do this, you’ll need to use a rag. For garage walls that are made from rough materials such as bricks or drywall, you have to use a broom to downward sweep the walls. This will help remove some of the dirt and dust that has accumulated in it over time. And if you happen to see any cobwebs, you can use the broom for removing them as well.

Step #3 to clean garage door

– This next step is all about the floor of your garage. Again, you’ll have to use a broom to sweep all of the accumulated dust and dirt on the floor. Just make sure that you’re not going to miss any spots or difficult-to-reach areas and corners. Some garage floors need more significant cleaning. For those floors, you’ll need to use a garden hose and pair it with a gentle cleanser. Any remaining water could be removed with the use of a squeegee.

Step #4 to a clean garage door

– Up next is your garage door. When it comes to cleaning your garage door, you need to remember one thing and that’s to clean it according to its material. There are materials that only require the door to be rinsed off with a hose and wiped down with a sponge and a mixture of dish detergent and water. This is the recommended cleaning method for garage doors that are made of vinyl, fiberglass, or steel.

Step #5 to a clean garage door

– You also need to include your door frames in the cleaning process. It might be hiding some caked-on dirt and if they are then you need to remove those too. All it would take is a simple scrubbing and you can simply hose it off afterward. But if the door frame requires something more complicated, such as stripping, staining, or painting, then you might need to call on professionals for help.

Following the above steps and setting them as your guide to a clean garage is sure to yield positive results. At the very least, you’re assured of a well-maintained garage that will be a delight to use for years to come.

Contact your nearest Garage door repair in lantana.

Five Factors that can Affect the Overall Garage Door Repair Expense

Repair and maintenance that you can do yourself are excellent for minor issues within your garage or overhead doors. The assistance and support of an expert garage repair service can be crucial in the event that a garage door problem becomes difficult or complex to solve on your own. 

garage door repair grapevine

Absolutely hiring the services of an expert garage door repair service in Texas is a significant expense. Let’s review the five most important factors from Garage Door Repair Grapevine TX that will determine the cost of your repair costs for garage doors:

1 Damage at the entrance:

The primary factor that determines the cost of repair for your door is the degree of damage and the type of repair to be carried out for your door. Small issues like worn-out components and spots may be addressed before you know it, but issues in the openers, sensors and other parts of the door may require more effort and cash to be invested.

2. Design of the garage and overhead doors:

The style of the door of your garage may play a role in the total repair cost. Certain doors can be fixed easily due to their typical designs of machinery, while others require greater time and effort to fix. Particularly, an older garage door will need greater labor and effort to repair as a result, the repair cost is likely to be higher.

3 Types of parts and components are used to make the entrance:

The numerous kinds of parts utilized in your garage can also impact the total repair costs. In general, costly garage doors will require more costly repairs. In terms of repair costs, are concerned, garage doors made of metal are cheaper than wood-based garage doors.

4 Finalization at the front door

While it’s not a necessity, however, some homeowners like having their garage doors completed and colored to match their home. If you would like and wish to do this after the repair, this will require extra costs.

5 Service Cost:

The cost of a service provided by different garage repair companies or businesses in Texas will differ from one another, and this is evidently affecting or influencing the total cost of repair. Certain repair services require low-cost solutions, while others charge a lot, especially during emergency repairs and maintenance calls to your garage door. So, it is essential to check the minimum cost of the particular service you are using before deciding which service you want to work with.

Last but not last, do not risk the safety or safety of the family for the cost of a small amount of money. Choosing a licensed, certified and insurance-backed garage door repair service is a good idea. They will offer fast and prompt repairs and also excellent work. It is also important to be sure that the company offers a warranty for their repair and replacement of parts. This will ensure that your repairs will be protected.

How do you remove the Garage Door Panel?

Garage Door Repair Austin TX

Removing Garage Door Panel

Due to their highly mobile nature, garage door parts are susceptible to damage, metal fatigue, distortions, and other damage periodically. They all require replacement frequently. Prior to their replacements will be completed, they should be taken off.

The next article will explain, in a step-wise manner, the steps to take off the garage door’s panels to inform homeowners and visitors about what to do in the event that their garage door panels experience problems.

To complete these steps to be successful, you will require the tools listed below, and the equipment is needed: ladder, vise clamps, hammers and ratcheting nut drivers, bits and power drills, knee pads, scrap boards of 2-by-4 inches, and a garage door section with four panels.

Step 1: Turn off an Automatic Garage Door Opener

To avoid shock, the garage door opener must be shut off by disconnecting the power as well as the central arm. This can be done by first lifting the door.

Step 2: Remove the Tension Springs

This is the process of separating the tension springs from turnbuckles that keep them in place with the help of drills powered by electricity and bits. Because the tension springs contain a significant amount of energy it is important to take care to prevent any accidents.

Step 3 Step III: Reduce the Doors

The door is then gently lowered with the aid of two 2-by-4 inch boards to about 3 – or 4-inches above the ground, to allow for getting rid of the lower panel.

Step 4: Secure the upper parts of the Garage Door.

This can be done by attaching vice clamps on the tracks for garage doors which are under the bearings on the two panels. This will keep that the doors fall down when the props of 2-by-4 inches are removed.

Step V Unlock bolts from the brackets.

It is best to do this by making use of a ratcheting driver. It is designed to assist in getting rid of the bottom panel.

Step Six: Take off the Panel

The garage door panel must eventually be removed by losing the bolts holding the lower panels to the brackets in the middle. The garage door can be opened for a repair to the garage door panel or the installation of a garage door panel.

Action Call Action

The typical homeowner may not possess all the tools needed to carry out the mentioned tasks. That, coupled with the dangers involved in this job or the removal of the garage door panels and the absence of expertise in the field for the average homeowner will make outsourcing service to a certified garage door service is by no means a necessity.

The Austin, Texas area and its surrounding areas The Austin Home Garage Doors business are the most prominent because it has an abundance of knowledge due to operating for quite a while and is in possession of the necessary tools required to complete the tasks at hand; and also has an expert team of and trained technicians.

How to Choose a Good overhead garage doors Austin?

Gatage Door Repair Austin TX

Choosing The Best Garage Door in Austin Texas

Austin is an ideal city to live in if you’re seeking a reliable Overhead Garage Doors Austin. Garage springs on doors Austin are very popular all over the world due to the many benefits they bring. When you’re buying or renovating a home it is likely that the garage door will seem to be not the primary thing people think of, however, it’s an essential feature. 

The overhead garage door can be a security feature for your house and adds to the overall look and feel of your home. In this post, we’ll discuss specifically how to pick the best overhead garage doors for Austin.

Let’s now discuss some important guidelines on the best overhead garage doors that are suitable for Austin. You must pay close attention to the following factors.

It is important to first determine the opening in your garage and the place you’ll build this door. It is important to take the measurements with care so that you aren’t on the wrong side.

You now need to figure out which kind of door is best suited to your home. Overhead garage doors are available in a variety of designs, including single sectionals and rolling sectionals. 

Popular designs might feature flat surfaces, plains, panels, or some more ornate designs. The best thing to do is to snap an image of your home and then search for various products.

The next thing you should choose is the right materials for the garage doors. The design and style you select will usually determine the type of material that the garage door will be made of. 

It is possible to choose wood doors or rolling sections, or single doors according to your preferences. 

If you wish, you can even paint them according to your preferences.

The other thing to consider is to determine whether you wish to put in a quality garage door opener. It is necessary to work to be a master in this area.

Finally, it is essential to be sure to shop around Austin. There are many retailers that offer services at different costs and it is important to evaluate various prices to get the most effective doors.

This article was all about selecting the most efficient overhead garage doors in Austin. It is important to go through this article thoroughly for more details. It can be a great source of information and help. 

Enjoy yourself and have fun while you move forward in the correct direction.

Page 1 of 2

Powered by WordPress & Theme by Anders Norén